全国咨询热线:021 6508 7716 全国热线电话:137 0168 5332

新闻资讯

News
News 新闻中心 新闻资讯

史上最全晶圆专业术语

Date: 2018-06-05
Views: 14

Acceptor - An element, such as boron, indium, and gallium used to create a free hole in a semiconductor. The acceptor atoms are required to have one less valence electron than the semiconductor.
受主 - 一种用来在半导体中形成空穴的元素,比如硼、铟和镓。受主原子必须比半导体元素少一价电子
Alignment Precision - Displacement of patterns that occurs during the photolithography process.
套准精度 - 在光刻工艺中转移图形的精度。
Anisotropic - A process of etching that has very little or no undercutting
 
各向异性 - 在蚀刻过程中,只做少量或不做侧向凹刻。
Area Contamination - Any foreign particles or material that are found on the surface of a wafer. This is viewed as discolored or smudged, and it is the result of stains, fingerprints, water spots, etc.
沾污区域 - 任何在晶圆片表面的外来粒子或物质。由沾污、手印和水滴产生的污染。
Azimuth, in Ellipsometry - The angle measured between the plane of incidence and the major axis of the ellipse.
椭圆方位角 - 测量入射面和主晶轴之间的角度。
Backside - The bottom surface of a silicon wafer. (Note: This term is not preferred; instead, use ‘back surface’.)
背面 - 晶圆片的底部表面。(注:不推荐该术语,建议使用“背部表面”)
Base Silicon Layer - The silicon wafer that is located underneath the insulator layer, which supports the silicon film on top of the wafer.
底部硅层 - 在绝缘层下部的晶圆片,是顶部硅层的基础。
Bipolar - Transistors that are able to use both holes and electrons as charge carriers.
双极晶体管 - 能够采用空穴和电子传导电荷的晶体管。
Bonded Wafers - Two silicon wafers that have been bonded together by silicon dioxide, which acts as an insulating layer.
绑定晶圆片 - 两个晶圆片通过二氧化硅层结合到一起,作为绝缘层。
Bonding Interface - The area where the bonding of two wafers occurs.
绑定面 - 两个晶圆片结合的接触区。
Buried Layer - A path of low resistance for a current moving in a device. Many of these dopants are antimony and arsenic.
埋层 - 为了电路电流流动而形成的低电阻路径,搀杂剂是锑和砷。
Buried Oxide Layer (BOX) - The layer that insulates between the two wafers.
氧化埋层(BOX) - 在两个晶圆片间的绝缘层。
Carrier - Valence holes and conduction electrons that are capable of carrying a charge through a solid surface in a silicon wafer.
载流子 - 晶圆片中用来传导电流的空穴或电子。
Chemical-Mechanical Polish (CMP) - A process of flattening and polishing wafers that utilizes both chemical removal and mechanical buffing. It is used during the fabrication process.
化学-机械抛光(CMP) - 平整和抛光晶圆片的工艺,采用化学移除和机械抛光两种方式。此工艺在前道工艺中使用。
Chuck Mark - A mark found on either surface of a wafer, caused by either a robotic end effector, a chuck, or a wand.
卡盘痕迹 - 在晶圆片任意表面发现的由机械手、卡盘或托盘造成的痕迹。
Cleavage Plane - A fracture plane that is preferred.
解理面 - 破裂面
Crack - A mark found on a wafer that is greater than 0.25 mm in length.
裂纹 - 长度大于0.25毫米的晶圆片表面微痕。
Crater - Visible under diffused illumination, a surface imperfection on a wafer that can be distinguished individually.
微坑 - 在扩散照明下可见的,晶圆片表面可区分的缺陷。
Conductivity (electrical) - A measurement of how easily charge carriers can flow throughout a material.
传导性(电学方面) - 一种关于载流子通过物质难易度的测量指标 。
Conductivity Type - The type of charge carriers in a wafer, such as “N-type” and “P-type”.
导电类型 - 晶圆片中载流子的类型,N型和P型。
Contaminant, Particulate (see light point defect)
污染微粒 (参见光点缺陷)
Contamination Area - An area that contains particles that can negatively affect the characteristics of a silicon wafer.
沾污区域 - 部分晶圆片区域被颗粒沾污,造成不利特性影响。
Contamination Particulate - Particles found on the surface of a silicon wafer.
沾污颗粒 - 晶圆片表面上的颗粒。
Crystal Defect - Parts of the crystal that contain vacancies and dislocations that can have an impact on a circuit’s electrical performance.
晶体缺陷 - 部分晶体包含的、会影响电路性能的空隙和层错。
Crystal Indices (see Miller indices)
晶体指数 (参见米勒指数)
Depletion Layer - A region on a wafer that contains an electrical field that sweeps out charge carriers.
耗尽层 - 晶圆片上的电场区域,此区域排除载流子。
Dimple - A concave depression found on the surface of a wafer that is visible to the eye under the correct lighting conditions.
表面起伏 - 在合适的光线下通过肉眼可以发现的晶圆片表面凹陷。
Donor - A contaminate that has donated extra “free” electrons, thus making a wafer “N-Type”.
施主 - 可提供“自由”电子的搀杂物,使晶圆片呈现为N型。
Dopant - An element that contributes an electron or a hole to the conduction process, thus altering the conductivity. Dopants for silicon wafers are found in Groups III and V of the Periodic Table of the Elements.
搀杂剂 - 可以为传导过程提供电子或空穴的元素,此元素可以改变传导特性。晶圆片搀杂 剂可以在元素周期表的III 和 V族元素中发现。
Doping - The process of the donation of an electron or hole to the conduction process by a dopant.
掺杂 - 把搀杂剂掺入半导体,通常通过扩散或离子注入工艺实现。
Edge Chip and Indent - An edge imperfection that is greater than 0.25 mm.
芯片边缘和缩进 - 晶片中不完整的边缘部分超过0.25毫米。
Edge Exclusion Area - The area located between the fixed quality area and the periphery of a wafer. (This varies according to the dimensions of the wafer.)
边缘排除区域 - 位于质量保证区和晶圆片外围之间的区域。(根据晶圆片的尺寸不同而有所不同。)
Edge Exclusion, Nominal (EE) - The distance between the fixed quality area and the periphery of a wafer.
名义上边缘排除(EE) - 质量保证区和晶圆片外围之间的距离。
Edge Profile - The edges of two bonded wafers that have been shaped either chemically or mechanically.
边缘轮廓 - 通过化学或机械方法连接起来的两个晶圆片边缘。
Etch - A process of chemical reactions or physical removal to rid the wafer of excess materials.
蚀刻 - 通过化学反应或物理方法去除晶圆片的多余物质。
Fixed Quality Area (FQA) - The area that is most central on a wafer surface.
质量保证区(FQA) - 晶圆片表面中央的大部分。
Flat - A section of the perimeter of a wafer that has been removed for wafer orientation purposes.
平边 - 晶圆片圆周上的一个小平面,作为晶向定位的依据。
Flat Diameter - The measurement from the center of the flat through the center of the wafer to the opposite edge of the wafer. (Perpendicular to the flat)
平口直径 - 由小平面的中心通过晶圆片中心到对面边缘的直线距离。
Four-Point Probe - Test equipment used to test resistivity of wafers.
四探针 - 测量半导体晶片表面电阻的设备。
Furnace and Thermal Processes - Equipment with a temperature gauge used for processing wafers. A constant temperature is required for the process.
炉管和热处理 - 温度测量的工艺设备,具有恒定的处理温度。
Front Side - The top side of a silicon wafer. (This term is not preferred; use front surface instead.)
正面 - 晶圆片的顶部表面(此术语不推荐,建议使用“前部表面”)。
Goniometer - An instrument used in measuring angles.
角度计 - 用来测量角度的设备。
Gradient, Resistivity (not preferred; see resistivity variation)
电阻梯度 (不推荐使用,参见“电阻变化”)
Groove - A scratch that was not completely polished out.
凹槽 - 没有被完全清除的擦伤。
Hand Scribe Mark - A marking that is hand scratched onto the back surface of a wafer for identification purposes.
手工印记 - 为区分不同的晶圆片而手工在背面做出的标记。
Haze - A mass concentration of surface imperfections, often giving a hazy appearance to the wafer.
雾度 - 晶圆片表面大量的缺陷,常常表现为晶圆片表面呈雾状。
Hole - Similar to a positive charge, this is caused by the absence of a valence electron.
空穴 - 和正电荷类似,是由缺少价电子引起的。
Ingot - A cylindrical solid made of polycrystalline or single crystal silicon from which wafers are cut.
晶锭 - 由多晶或单晶形成的圆柱体,晶圆片由此切割而成。
Laser Light-Scattering Event - A signal pulse that locates surface imperfections on a wafer.
激光散射 - 由晶圆片表面缺陷引起的脉冲信号。
Lay - The main direction of surface texture on a wafer.
层 - 晶圆片表面结构的主要方向。
Light Point Defect (LPD) (Not preferred; see localized light-scatterer)
光点缺陷(LPD) (不推荐使用,参见“局部光散射”)
Lithography - The process used to transfer patterns onto wafers.
光刻 - 从掩膜到圆片转移的过程。
Localized Light-Scatterer - One feature on the surface of a wafer, such as a pit or a scratch that scatters light. It is also called a light point defect.
局部光散射 - 晶圆片表面特征,例如小坑或擦伤导致光线散射,也称为光点缺陷。
Lot - Wafers of similar sizes and characteristics placed together in a shipment.
批次 - 具有相似尺寸和特性的晶圆片一并放置在一个载片器内。
Majority Carrier - A carrier, either a hole or an electron that is dominant in a specific region, such as electrons in an N-Type area.
多数载流子 - 一种载流子,在半导体材料中起支配作用的空穴或电子,例如在N型中是电子。
Mechanical Test Wafer - A silicon wafer used for testing purposes.
机械测试晶圆片 - 用于测试的晶圆片。
Microroughness - Surface roughness with spacing between the impurities with a measurement of less than 100 μm.
微粗糙 - 小于100微米的表面粗糙部分。
Miller Indices, of a Crystallographic Plane - A system that utilizes three numbers to identify plan orientation in a crystal.
Miller索指数 - 三个整数,用于确定某个并行面。这些整数是来自相同系统的基本向量。
Minimal Conditions or Dimensions - The allowable conditions for determining whether or not a wafer is considered acceptable.
最小条件或方向 - 确定晶圆片是否合格的允许条件。
Minority Carrier - A carrier, either a hole or an electron that is not dominant in a specific region, such as electrons in a P-Type area.
少数载流子 - 在半导体材料中不起支配作用的移动电荷,在P型中是电子,在N型中是空穴。
Mound - A raised defect on the surface of a wafer measuring more than 0.25 mm.
堆垛 - 晶圆片表面超过0.25毫米的缺陷。
Notch - An indent on the edge of a wafer used for orientation purposes.
凹槽 - 晶圆片边缘上用于晶向定位的小凹槽。
Orange Peel - A roughened surface that is visible to the unaided eye.
桔皮 - 可以用肉眼看到的粗糙表面
Orthogonal Misorientation -
直角定向误差 -
Particle - A small piece of material found on a wafer that is not connected with it.
颗粒 - 晶圆片上的细小物质。
Particle Counting - Wafers that are used to test tools for particle contamination.
颗粒计算 - 用来测试晶圆片颗粒污染的测试工具。
Particulate Contamination - Particles found on the surface of a wafer. They appear as bright points when a collineated light is shined on the wafer.
颗粒污染 - 晶圆片表面的颗粒。
Pit - A non-removable imperfection found on the surface of a wafer.
深坑 - 一种晶圆片表面无法消除的缺陷。
Point Defect - A crystal defect that is an impurity, such as a lattice vacancy or an interstitial atom.
点缺陷 - 不纯净的晶缺陷,例如格子空缺或原子空隙。
Preferential Etch -
优先蚀刻 -
Premium Wafer - A wafer that can be used for particle counting, measuring pattern resolution in the photolithography process, and metal contamination monitoring. This wafer has very strict specifications for a specific usage, but looser specifications than the prime wafer.
测试晶圆片 - 影印过程中用于颗粒计算、测量溶解度和检测金属污染的晶圆片。对于具体应用该晶圆片有严格的要求,但是要比主晶圆片要求宽松些。
Primary Orientation Flat - The longest flat found on the wafer.
主定位边 - 晶圆片上最长的定位边。
Process Test Wafer - A wafer that can be used for processes as well as area cleanliness.
加工测试晶圆片 - 用于区域清洁过程中的晶圆片。
Profilometer - A tool that is used for measuring surface topography.
表面形貌剂 - 一种用来测量晶圆片表面形貌的工具。
Resistivity (Electrical) - The amount of difficulty that charged carriers have in moving throughout material.
电阻率(电学方面) - 材料反抗或对抗电荷在其中通过的一种物理特性。
Required - The minimum specifications needed by the customer when ordering wafers.
必需 - 订购晶圆片时客户必须达到的最小规格。
Roughness - The texture found on the surface of the wafer that is spaced very closely together.
粗糙度 - 晶圆片表面间隙很小的纹理。
Saw Marks - Surface irregularities
锯痕 - 表面不规则。
Scan Direction - In the flatness calculation, the direction of the subsites.
扫描方向 - 平整度测量中,局部平面的方向。
Scanner Site Flatness -
局部平整度扫描仪 -
Scratch - A mark that is found on the wafer surface.
擦伤 - 晶圆片表面的痕迹。
Secondary Flat - A flat that is smaller than the primary orientation flat. The position of this flat determines what type the wafer is, and also the orientation of the wafer.
第二定位边 - 比主定位边小的定位边,它的位置决定了晶圆片的类型和晶向。
Shape -
形状 -
Site - An area on the front surface of the wafer that has sides parallel and perpendicular to the primary orientation flat. (This area is rectangular in shape)
局部表面 - 晶圆片前面上平行或垂直于主定位边方向的区域。
Site Array - a neighboring set of sites
局部表面系列 - 一系列的相关局部表面。
Site Flatness -
局部平整 -
Slip - A defect pattern of small ridges found on the surface of the wafer.
划伤 - 晶圆片表面上的小皱造成的缺陷。
Smudge - A defect or contamination found on the wafer caused by fingerprints.
污迹 - 晶圆片上指纹造成的缺陷或污染。
Sori -
Striation - Defects or contaminations found in the shape of a helix.
条痕 - 螺纹上的缺陷或污染。
Subsite, of a Site - An area found within the site, also rectangular. The center of the subsite must be located within the original site.
局部子表面 - 局部表面内的区域,也是矩形的。子站中心必须位于原始站点内部。
Surface Texture - Variations found on the real surface of the wafer that deviate from the reference surface.
表面纹理 - 晶圆片实际面与参考面的差异情况。
Test Wafer - A silicon wafer that is used in manufacturing for monitoring and testing purposes.
测试晶圆片 - 用于生产中监测和测试的晶圆片。
Thickness of Top Silicon Film - The distance found between the face of the top silicon film and the surface of the oxide layer.
顶部硅膜厚度 - 顶部硅层表面和氧化层表面间的距离。
Top Silicon Film - The layer of silicon on which semiconductor devices are placed. This is located on top of the insulating layer.
顶部硅膜 - 生产半导体电路的硅层,位于绝缘层顶部。
Total Indicator Reading (TIR) - The smallest distance between planes on the surface of the wafer.
总计指示剂数(TIR) - 晶圆片表面位面间的最短距离。
Virgin Test Wafer - A wafer that has not been used in manufacturing or other processes.
原始测试晶圆片 - 还没有用于生产或其他流程中的晶圆片。
Void - The lack of any sort of bond (particularly a chemical bond) at the site of bonding.
无效 - 在应该绑定的地方没有绑定(特别是化学绑定)。
Waves - Curves and contours found on the surface of the wafer that can be seen by the naked eye.
波浪 - 晶圆片表面通过肉眼能发现的弯曲和曲线。
Waviness - Widely spaced imperfections on the surface of a wafer.
波纹 - 晶圆片表面经常出现的缺陷。

回到顶部
News / Relative News More
2018 - 08 - 21
作为新一代的扫描测试设备,该超声波扫描显微镜在扫描方式和数据精确度方面有着更高的技术手段,而且获取出来的图像质量也会更有保证,所以受到用户的广泛选择,那么,人们选择超声波扫描显微镜的三大理由到底是什么呢?1、检测灵敏度高且数据精准很多用户对于超声波扫描显微镜哪个牌子好这个问题都有着不同的见解,但事实证明检测灵敏度高且数据精准都是该优秀显微镜所具备的产品特征,因其会根据实际应用中的不同问题来及时调整检测方案,同时,其也会利用超声波的优势来获取高精准的数据,从而满足高标准的科学实验需求。2、安全性好且噪音小与传统的显微镜设备对比,该超声波扫描显微镜在安全性方面的优势更为显着,其通过先进的技术从而来有效降低设备对人体的辐射,而且对于检测物也有极高的安全保障措施,另外,该超声波扫描显微镜在生产作业时不会产生任何噪音,因此也能有效减少噪音对周围居民的休息及环境所造成的影响。3、使用寿命长且价格合理超...
2018 - 08 - 21
如今众多领域都需要应用到专业的超声波扫描显微镜,它可以在工业的生产线中利用手工扫描的方法来检测出所生产的零件是否具有缺陷,这样在生产的过程中为工人提供极大的便利的同时也越发让人们离不开它。那么该怎么进行保养使得超声波扫描显微镜的使用时间较长。  一、不要在高温环境下长时间使用显微镜  在夏季很多场合的气温过高,因此如果需要使用超声波扫描显微镜时需要在空调房中使用,因为如果当周围温度过高时会引起显微镜发生火灾,这样不仅会让自己处于危险的环境中,也会给公司造成经济损失。  二、避免磁场的干扰  在使用超声波扫描显微镜时必须要避开强力震动的电磁场,因为磁场会造成显微镜的暂时性失效,使用它将不会有任何的效果,如果环境中有任何具有带磁性的产品时也要将它远离超声波扫描显微镜。所以在挑选超声波扫描显微镜的时候一定要注意尽量挑选防静电能力强的保护膜。  三、保持元器件的干燥  为了保持超声波扫描显微镜元器...
2018 - 08 - 16
随着超声波扫描显微检测技术的持续发展,超声波检测仪的功能更加具体化智能化被广泛的运用于测试气体压力系统,检测管道泄漏,材料处理系统等领域。并在为广大客户群体提供对各种精密机器设备的检测工作当中起到了不可或缺的作用。那么选择使用超声波检测仪具体可以有哪些好处?一、超声波检测仪的性价比高作为营利为目的的组织机构,不管什么类型的企业都非常看重日常生产工作的效益,使用一款工作效率高工作效益又好的仪器工具,对企业起到的作用往往也是不容忽视的。作为一款系统强大高性能的检测工具,顾客可以依据企业日常工作的精细度,参考不同类型不同品牌的超声波检测仪报价及图片大全,选择合适的超声波检测仪,有效减少企业技术成本同时又能保障日常工作中数据的准确率。二、超声波检测仪可以有效的保障日常工作的安全现在市面上研发制作检测仪器的厂家有很多,功能各异。在日常的管道泄漏检测,设备安全监测、生命财产安全保护的工作中,超声波检测...
2018 - 08 - 16
超声波检测仪凭借其小巧精致易于操作的显著优点在现代社会中不同的领域都得到了广泛的应用,对于超声波检测仪的使用者而言该仪器能否正常运行将会直接影响到其日常工作。那么超声波检测仪在实际操控的过程中都需要注意哪些事项呢?超声波检测仪厂家口碑好将在下文中对这些事项予以介绍。第一、避免人为频繁开关机众所周知很多仪器在使用过程中如若遭遇人为刻意的开关机操作都会对仪器本身产生些许损害,对于作为一种精密检测仪器的超声波检测仪而言也是如此。因此使用者应当尽量避免人为的对其进行频繁开关机操作,如若无意中将超声波检测仪关停则应当稍等片刻再做开启操作。第二、远离强力磁场超声波检测仪的正常运行离不开超声波的支持,但是有一些因素会对超声波产生一定的干扰诸如强力磁场。这就要求超声波检测仪的操控人员操控该仪器之时应当注重周边的环境,尽量与强力磁场保持一定的距离。第三、不得擅自拆装任何仪器或设备在长期运行的过程中难免会遭遇...
Copyright ©2017 - 2019 科视达
犀牛云提供企业云服务
科视达(中国)有限公司
科视达(上海)国际贸易有限公司
上海总部:( 021 ) 6508-7716  (021)6508-3319
北京分部:  ( 010 ) 6708-0981
深圳分部:  ( 0755 ) 8379-0503 ( 0755 ) 8272-4458
成都分部:  ( 028 ) 8613-2728
武汉分部:  177 4975 1126
香港分部:  ( 00852 ) 2854-3911
扫一扫
浏览手机云网站吧