全国咨询热线:021 6508 7716 全国热线电话:137 0168 5332

新闻资讯

News
News 新闻中心 新闻资讯

史上最全晶圆专业术语

Date: 2018-06-05
Views: 1401

Acceptor - An element, such as boron, indium, and gallium used to create a free hole in a semiconductor. The acceptor atoms are required to have one less valence electron than the semiconductor.
受主 - 一种用来在半导体中形成空穴的元素,比如硼、铟和镓。受主原子必须比半导体元素少一价电子
Alignment Precision - Displacement of patterns that occurs during the photolithography process.
套准精度 - 在光刻工艺中转移图形的精度。
Anisotropic - A process of etching that has very little or no undercutting
 
各向异性 - 在蚀刻过程中,只做少量或不做侧向凹刻。
Area Contamination - Any foreign particles or material that are found on the surface of a wafer. This is viewed as discolored or smudged, and it is the result of stains, fingerprints, water spots, etc.
沾污区域 - 任何在晶圆片表面的外来粒子或物质。由沾污、手印和水滴产生的污染。
Azimuth, in Ellipsometry - The angle measured between the plane of incidence and the major axis of the ellipse.
椭圆方位角 - 测量入射面和主晶轴之间的角度。
Backside - The bottom surface of a silicon wafer. (Note: This term is not preferred; instead, use ‘back surface’.)
背面 - 晶圆片的底部表面。(注:不推荐该术语,建议使用“背部表面”)
Base Silicon Layer - The silicon wafer that is located underneath the insulator layer, which supports the silicon film on top of the wafer.
底部硅层 - 在绝缘层下部的晶圆片,是顶部硅层的基础。
Bipolar - Transistors that are able to use both holes and electrons as charge carriers.
双极晶体管 - 能够采用空穴和电子传导电荷的晶体管。
Bonded Wafers - Two silicon wafers that have been bonded together by silicon dioxide, which acts as an insulating layer.
绑定晶圆片 - 两个晶圆片通过二氧化硅层结合到一起,作为绝缘层。
Bonding Interface - The area where the bonding of two wafers occurs.
绑定面 - 两个晶圆片结合的接触区。
Buried Layer - A path of low resistance for a current moving in a device. Many of these dopants are antimony and arsenic.
埋层 - 为了电路电流流动而形成的低电阻路径,搀杂剂是锑和砷。
Buried Oxide Layer (BOX) - The layer that insulates between the two wafers.
氧化埋层(BOX) - 在两个晶圆片间的绝缘层。
Carrier - Valence holes and conduction electrons that are capable of carrying a charge through a solid surface in a silicon wafer.
载流子 - 晶圆片中用来传导电流的空穴或电子。
Chemical-Mechanical Polish (CMP) - A process of flattening and polishing wafers that utilizes both chemical removal and mechanical buffing. It is used during the fabrication process.
化学-机械抛光(CMP) - 平整和抛光晶圆片的工艺,采用化学移除和机械抛光两种方式。此工艺在前道工艺中使用。
Chuck Mark - A mark found on either surface of a wafer, caused by either a robotic end effector, a chuck, or a wand.
卡盘痕迹 - 在晶圆片任意表面发现的由机械手、卡盘或托盘造成的痕迹。
Cleavage Plane - A fracture plane that is preferred.
解理面 - 破裂面
Crack - A mark found on a wafer that is greater than 0.25 mm in length.
裂纹 - 长度大于0.25毫米的晶圆片表面微痕。
Crater - Visible under diffused illumination, a surface imperfection on a wafer that can be distinguished individually.
微坑 - 在扩散照明下可见的,晶圆片表面可区分的缺陷。
Conductivity (electrical) - A measurement of how easily charge carriers can flow throughout a material.
传导性(电学方面) - 一种关于载流子通过物质难易度的测量指标 。
Conductivity Type - The type of charge carriers in a wafer, such as “N-type” and “P-type”.
导电类型 - 晶圆片中载流子的类型,N型和P型。
Contaminant, Particulate (see light point defect)
污染微粒 (参见光点缺陷)
Contamination Area - An area that contains particles that can negatively affect the characteristics of a silicon wafer.
沾污区域 - 部分晶圆片区域被颗粒沾污,造成不利特性影响。
Contamination Particulate - Particles found on the surface of a silicon wafer.
沾污颗粒 - 晶圆片表面上的颗粒。
Crystal Defect - Parts of the crystal that contain vacancies and dislocations that can have an impact on a circuit’s electrical performance.
晶体缺陷 - 部分晶体包含的、会影响电路性能的空隙和层错。
Crystal Indices (see Miller indices)
晶体指数 (参见米勒指数)
Depletion Layer - A region on a wafer that contains an electrical field that sweeps out charge carriers.
耗尽层 - 晶圆片上的电场区域,此区域排除载流子。
Dimple - A concave depression found on the surface of a wafer that is visible to the eye under the correct lighting conditions.
表面起伏 - 在合适的光线下通过肉眼可以发现的晶圆片表面凹陷。
Donor - A contaminate that has donated extra “free” electrons, thus making a wafer “N-Type”.
施主 - 可提供“自由”电子的搀杂物,使晶圆片呈现为N型。
Dopant - An element that contributes an electron or a hole to the conduction process, thus altering the conductivity. Dopants for silicon wafers are found in Groups III and V of the Periodic Table of the Elements.
搀杂剂 - 可以为传导过程提供电子或空穴的元素,此元素可以改变传导特性。晶圆片搀杂 剂可以在元素周期表的III 和 V族元素中发现。
Doping - The process of the donation of an electron or hole to the conduction process by a dopant.
掺杂 - 把搀杂剂掺入半导体,通常通过扩散或离子注入工艺实现。
Edge Chip and Indent - An edge imperfection that is greater than 0.25 mm.
芯片边缘和缩进 - 晶片中不完整的边缘部分超过0.25毫米。
Edge Exclusion Area - The area located between the fixed quality area and the periphery of a wafer. (This varies according to the dimensions of the wafer.)
边缘排除区域 - 位于质量保证区和晶圆片外围之间的区域。(根据晶圆片的尺寸不同而有所不同。)
Edge Exclusion, Nominal (EE) - The distance between the fixed quality area and the periphery of a wafer.
名义上边缘排除(EE) - 质量保证区和晶圆片外围之间的距离。
Edge Profile - The edges of two bonded wafers that have been shaped either chemically or mechanically.
边缘轮廓 - 通过化学或机械方法连接起来的两个晶圆片边缘。
Etch - A process of chemical reactions or physical removal to rid the wafer of excess materials.
蚀刻 - 通过化学反应或物理方法去除晶圆片的多余物质。
Fixed Quality Area (FQA) - The area that is most central on a wafer surface.
质量保证区(FQA) - 晶圆片表面中央的大部分。
Flat - A section of the perimeter of a wafer that has been removed for wafer orientation purposes.
平边 - 晶圆片圆周上的一个小平面,作为晶向定位的依据。
Flat Diameter - The measurement from the center of the flat through the center of the wafer to the opposite edge of the wafer. (Perpendicular to the flat)
平口直径 - 由小平面的中心通过晶圆片中心到对面边缘的直线距离。
Four-Point Probe - Test equipment used to test resistivity of wafers.
四探针 - 测量半导体晶片表面电阻的设备。
Furnace and Thermal Processes - Equipment with a temperature gauge used for processing wafers. A constant temperature is required for the process.
炉管和热处理 - 温度测量的工艺设备,具有恒定的处理温度。
Front Side - The top side of a silicon wafer. (This term is not preferred; use front surface instead.)
正面 - 晶圆片的顶部表面(此术语不推荐,建议使用“前部表面”)。
Goniometer - An instrument used in measuring angles.
角度计 - 用来测量角度的设备。
Gradient, Resistivity (not preferred; see resistivity variation)
电阻梯度 (不推荐使用,参见“电阻变化”)
Groove - A scratch that was not completely polished out.
凹槽 - 没有被完全清除的擦伤。
Hand Scribe Mark - A marking that is hand scratched onto the back surface of a wafer for identification purposes.
手工印记 - 为区分不同的晶圆片而手工在背面做出的标记。
Haze - A mass concentration of surface imperfections, often giving a hazy appearance to the wafer.
雾度 - 晶圆片表面大量的缺陷,常常表现为晶圆片表面呈雾状。
Hole - Similar to a positive charge, this is caused by the absence of a valence electron.
空穴 - 和正电荷类似,是由缺少价电子引起的。
Ingot - A cylindrical solid made of polycrystalline or single crystal silicon from which wafers are cut.
晶锭 - 由多晶或单晶形成的圆柱体,晶圆片由此切割而成。
Laser Light-Scattering Event - A signal pulse that locates surface imperfections on a wafer.
激光散射 - 由晶圆片表面缺陷引起的脉冲信号。
Lay - The main direction of surface texture on a wafer.
层 - 晶圆片表面结构的主要方向。
Light Point Defect (LPD) (Not preferred; see localized light-scatterer)
光点缺陷(LPD) (不推荐使用,参见“局部光散射”)
Lithography - The process used to transfer patterns onto wafers.
光刻 - 从掩膜到圆片转移的过程。
Localized Light-Scatterer - One feature on the surface of a wafer, such as a pit or a scratch that scatters light. It is also called a light point defect.
局部光散射 - 晶圆片表面特征,例如小坑或擦伤导致光线散射,也称为光点缺陷。
Lot - Wafers of similar sizes and characteristics placed together in a shipment.
批次 - 具有相似尺寸和特性的晶圆片一并放置在一个载片器内。
Majority Carrier - A carrier, either a hole or an electron that is dominant in a specific region, such as electrons in an N-Type area.
多数载流子 - 一种载流子,在半导体材料中起支配作用的空穴或电子,例如在N型中是电子。
Mechanical Test Wafer - A silicon wafer used for testing purposes.
机械测试晶圆片 - 用于测试的晶圆片。
Microroughness - Surface roughness with spacing between the impurities with a measurement of less than 100 μm.
微粗糙 - 小于100微米的表面粗糙部分。
Miller Indices, of a Crystallographic Plane - A system that utilizes three numbers to identify plan orientation in a crystal.
Miller索指数 - 三个整数,用于确定某个并行面。这些整数是来自相同系统的基本向量。
Minimal Conditions or Dimensions - The allowable conditions for determining whether or not a wafer is considered acceptable.
最小条件或方向 - 确定晶圆片是否合格的允许条件。
Minority Carrier - A carrier, either a hole or an electron that is not dominant in a specific region, such as electrons in a P-Type area.
少数载流子 - 在半导体材料中不起支配作用的移动电荷,在P型中是电子,在N型中是空穴。
Mound - A raised defect on the surface of a wafer measuring more than 0.25 mm.
堆垛 - 晶圆片表面超过0.25毫米的缺陷。
Notch - An indent on the edge of a wafer used for orientation purposes.
凹槽 - 晶圆片边缘上用于晶向定位的小凹槽。
Orange Peel - A roughened surface that is visible to the unaided eye.
桔皮 - 可以用肉眼看到的粗糙表面
Orthogonal Misorientation -
直角定向误差 -
Particle - A small piece of material found on a wafer that is not connected with it.
颗粒 - 晶圆片上的细小物质。
Particle Counting - Wafers that are used to test tools for particle contamination.
颗粒计算 - 用来测试晶圆片颗粒污染的测试工具。
Particulate Contamination - Particles found on the surface of a wafer. They appear as bright points when a collineated light is shined on the wafer.
颗粒污染 - 晶圆片表面的颗粒。
Pit - A non-removable imperfection found on the surface of a wafer.
深坑 - 一种晶圆片表面无法消除的缺陷。
Point Defect - A crystal defect that is an impurity, such as a lattice vacancy or an interstitial atom.
点缺陷 - 不纯净的晶缺陷,例如格子空缺或原子空隙。
Preferential Etch -
优先蚀刻 -
Premium Wafer - A wafer that can be used for particle counting, measuring pattern resolution in the photolithography process, and metal contamination monitoring. This wafer has very strict specifications for a specific usage, but looser specifications than the prime wafer.
测试晶圆片 - 影印过程中用于颗粒计算、测量溶解度和检测金属污染的晶圆片。对于具体应用该晶圆片有严格的要求,但是要比主晶圆片要求宽松些。
Primary Orientation Flat - The longest flat found on the wafer.
主定位边 - 晶圆片上最长的定位边。
Process Test Wafer - A wafer that can be used for processes as well as area cleanliness.
加工测试晶圆片 - 用于区域清洁过程中的晶圆片。
Profilometer - A tool that is used for measuring surface topography.
表面形貌剂 - 一种用来测量晶圆片表面形貌的工具。
Resistivity (Electrical) - The amount of difficulty that charged carriers have in moving throughout material.
电阻率(电学方面) - 材料反抗或对抗电荷在其中通过的一种物理特性。
Required - The minimum specifications needed by the customer when ordering wafers.
必需 - 订购晶圆片时客户必须达到的最小规格。
Roughness - The texture found on the surface of the wafer that is spaced very closely together.
粗糙度 - 晶圆片表面间隙很小的纹理。
Saw Marks - Surface irregularities
锯痕 - 表面不规则。
Scan Direction - In the flatness calculation, the direction of the subsites.
扫描方向 - 平整度测量中,局部平面的方向。
Scanner Site Flatness -
局部平整度扫描仪 -
Scratch - A mark that is found on the wafer surface.
擦伤 - 晶圆片表面的痕迹。
Secondary Flat - A flat that is smaller than the primary orientation flat. The position of this flat determines what type the wafer is, and also the orientation of the wafer.
第二定位边 - 比主定位边小的定位边,它的位置决定了晶圆片的类型和晶向。
Shape -
形状 -
Site - An area on the front surface of the wafer that has sides parallel and perpendicular to the primary orientation flat. (This area is rectangular in shape)
局部表面 - 晶圆片前面上平行或垂直于主定位边方向的区域。
Site Array - a neighboring set of sites
局部表面系列 - 一系列的相关局部表面。
Site Flatness -
局部平整 -
Slip - A defect pattern of small ridges found on the surface of the wafer.
划伤 - 晶圆片表面上的小皱造成的缺陷。
Smudge - A defect or contamination found on the wafer caused by fingerprints.
污迹 - 晶圆片上指纹造成的缺陷或污染。
Sori -
Striation - Defects or contaminations found in the shape of a helix.
条痕 - 螺纹上的缺陷或污染。
Subsite, of a Site - An area found within the site, also rectangular. The center of the subsite must be located within the original site.
局部子表面 - 局部表面内的区域,也是矩形的。子站中心必须位于原始站点内部。
Surface Texture - Variations found on the real surface of the wafer that deviate from the reference surface.
表面纹理 - 晶圆片实际面与参考面的差异情况。
Test Wafer - A silicon wafer that is used in manufacturing for monitoring and testing purposes.
测试晶圆片 - 用于生产中监测和测试的晶圆片。
Thickness of Top Silicon Film - The distance found between the face of the top silicon film and the surface of the oxide layer.
顶部硅膜厚度 - 顶部硅层表面和氧化层表面间的距离。
Top Silicon Film - The layer of silicon on which semiconductor devices are placed. This is located on top of the insulating layer.
顶部硅膜 - 生产半导体电路的硅层,位于绝缘层顶部。
Total Indicator Reading (TIR) - The smallest distance between planes on the surface of the wafer.
总计指示剂数(TIR) - 晶圆片表面位面间的最短距离。
Virgin Test Wafer - A wafer that has not been used in manufacturing or other processes.
原始测试晶圆片 - 还没有用于生产或其他流程中的晶圆片。
Void - The lack of any sort of bond (particularly a chemical bond) at the site of bonding.
无效 - 在应该绑定的地方没有绑定(特别是化学绑定)。
Waves - Curves and contours found on the surface of the wafer that can be seen by the naked eye.
波浪 - 晶圆片表面通过肉眼能发现的弯曲和曲线。
Waviness - Widely spaced imperfections on the surface of a wafer.
波纹 - 晶圆片表面经常出现的缺陷。

回到顶部
News / Relative News More
2023 - 03 - 22
德国PVA显微镜是一类在现代实验室加工制造业中常用的一种较好显微镜。其特点是利用极化光来提高样品对比度和清晰度,促使研究人员可以更有效地观察和分析样品显微结构和构成。然而,在挑选德国PVA显微镜时,要考虑到许多因素,以保障选择较为适合您运用的仪器。下面将推荐一些关键的因素,以帮助选择PVA显微镜。在挑选PVA显微镜时,要考虑到所需要的分辩率,及其显微镜的镜头、数字摄像头和软件能否支持所需要的分辩率。在挑选这种显微镜时,考虑必须观察的样品类型和所需要的较大放大倍数。比如,如果你必须观察大中型样品,则需要一个拥有相对较低的放大倍数的显微镜。PVA显微镜使用的极化光源对样品观察具备较大影响。在挑选要考虑到它是否具备可调式的极化光源,以便您可以根据实际情况调整光源的强度与方向。考虑其镜头的类型、品质与数量。普遍的德国PVA显微镜镜头包括物镜、目镜和偏光镜头。您需要选择较为适合您运用的镜头。数字摄像...
2023 - 03 - 21
显微镜在医学和科研上有着广泛的应用,随着科学技术的不断发展,显微镜的种类和型号越来越多,声学扫描显微镜起源于上世纪的80年代,它是一种重要的三维观察设备,融合了超声波学信号检测和计算机的先进技术,工作频率处于超声频段,一般也被叫做超声显微镜。相对于普通的显微镜,它有哪些典型的优势,下面一起来了解一下。1.信号强度更加稳定显微镜的主要目的是用于成像,对于成像来说清晰度越好,成像效果就越明显。这种类型的显微镜利用超声波,在介质中的不同传播速度来进行成像,其传播速度和介质的种类有关。不管是何种类型的介质,都可以通过超声波在介质中传说的衰减情况,对被测物体进行扫描,通过反射来获得准确的信号,再转化成一定的电信号,从而能够观察到物体的内部,相对于传统的显微镜来说它的显像程度更加清晰,信号强度更加稳定。2.实现对物体的无损观察传统的显微镜需要通过对被检测物体进行一定的前处理并制作成压片来成像,而超声显...
2023 - 03 - 20
近十年来随着高科技的不断更迭进步,超声波检测仪已经成为了一种不可缺少的医疗仪器。它能够准确地测量出物体内部结构和表面形状等特征信息,为我们提供了更加准确、全面的诊疗判断,不仅能了解自己身体的情况,还能发现潜在的安全隐患。在医学检测仪器的领域,超声波的检测仪的优势是相当明显的。超声波的检测仪作为一种成熟的医学检测仪器,可以用于早期癌症筛查、胎儿畸形检测、肝脏结节检测等。检测仪具有准确、快速、无创伤等优势,是目前使用较为广泛的医学检测仪器之一。当前的超声波检测仪的原理其实很简单,检测仪是采用超声波的频率、相位和幅值对工件表面或内部缺陷进行探测。大多超声波的检测仪都是通过超声探头将声波发射到水中,当水在一定的压力和振动条件下被吸收产生共振时,超声信号会发生变化。根据声强衰减公式可以计算出传播的距离。因为检测仪的操作相当方便,其应用的范围也越来越广泛,尤其在妇产科领域得到了更为广泛的应用,能够轻松...
2023 - 03 - 17
超声波扫描显微镜是一项基于超声技术的显微成像技术,其应用领域广泛,包括医疗、工业制造、材料科学、生命科学等领域。该技术通过控制和操作超声波来实现对材料、组织或样品的成像,为相关领域的研究提供了有力支持。科视达将带你探讨超声波扫描显微的广阔前景。 在医疗领域中,超声波扫描显微成像技术常用于超声心动图、超声体层摄影、乳腺超声、骨科超声等方面。它透过皮肤和组织,实现了非侵入性的成像,因此被广泛应用于疾病诊断、手术指导和治疗监控。随着技术的发展和诊疗需求的增加,超声波扫描显微已扩展到更广阔的医学领域,包括皮肤、眼科、儿科等多个方面。在工业制造领域中,超声波扫描显微成像技术可以对内部材料结构进行非侵入式、无损的检测,从而提高制造质量和效率,避免因质量问题而带来的经济损失。它广泛应用于建筑材料、金属材料、电子元器件等领域,为相关企业提供了可靠的质量检测和监测手段。在材料科学领域中,超声波扫描显微成像技...
上海市黄兴路1728号东方蓝海国际广场2号楼1906室 北京市崇文门外大街5-3新世界太华公寓B座1115室 深圳市福田区华强北路1050号现代之窗B座20P 成都市锦里东路5号国嘉华庭A-29-1 湖北省武汉市东湖高新区光谷总部国际1号楼1栋1304 香港湾仔菲林明道8号大同大厦1504室
Copyright ©2017 - 2019 科视达
犀牛云提供云计算服务
科视达(中国)有限公司
科视达(上海)国际贸易有限公司
上海总部:( 021 ) 6508-7716  (021)6508-3319
北京分部:  ( 010 ) 6708-0981
深圳分部:  ( 0755 ) 8379-0503 ( 0755 ) 8272-4458
成都分部:  ( 028 ) 8613-2728
武汉分部:  177 4975 1126
香港分部:  ( 00852 ) 2854-3911
扫一扫
浏览手机云网站吧